Monel K500 UNS N05500 2.4375 Nickel Alloy

price:
Contact customer service
Heat Treatment
Cold Processing
Hot Working

Monel K500 UNS N05500 2.4375 Nickel Alloy

Monel K500 UNS N05500 2.4375 Nickel Alloy

Monel K500 UNS N05500 2.4375 Nickel Alloy

With over 35 years of industry expertise, Fushun has the industry knowledge and resources to find you the metal products that you need for your specific industry applications. We are in stock and ready to quickly deliver hard-to-find metals. Our ISO 9001-certified metal supply is one of the most comprehensive selections on the market. We provide timely customer support and quick delivery on all quantities of our in stock products.

 

Contact us for more information regarding our nickel alloy manufacturing and distribution options.  Fushun is your trusted nickel alloy supplier for all types of Nickel alloy material.

Introduce

Monel nickel-copper alloy K-500 combines the excellent corrosion resistance characteristic of Monel alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanimum to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated thoughout the matrix. The thermal processing used to effect precipitation is commonly called age hardening or aging.

Back to Top

Application

Typical applications for Monel Alloy K-500 products are chains and cables, fasteners and springs for marine service; pump and valve components for chemical processing; doctor blades and scrapers for pulp processing in paper production; oil well drill collars and instruments, pump shafts and impellers, non-magnetic housings, safety lifts and valves for oil and gas production; and sensors and other electronic components.

Back to Top

Chemical Composition

Trade Name ASTM/AISI

Alloy type

UNS %Cu %Al %Ti %Fe %Mn %Si %Ni
Monel K-500 B 865 N05500 27–33 2.3–3.15 0.35–0.85 2.0 max 1.5 max 0.5 max 63 min
Back to Top

Mechanical Properties Nominal Mechanical Property Ranges(a)

Form and Condition Tensile Strength,

1000 psi

Yield Strength

0.2% offset, 1000 psi

Elongation

%

Hardness

Rockwell

Sheet, Cold Rolled, Annealed

Plate

Hot-Finished

Hot-Finished, Aged(b)

90-105

 

90-135

140-180

40-65

 

40-110

100-135

45-25

 

45-20

30-20

85B max

 

75B-26C

27-37C

Back to Top

Corrosion Resistance

The corrosion resistance of Monel alloy K-500 is subtantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments. Monel alloy K-500 has been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking. There was some tightly adherent black scale. Hardness of the specimens ranged from 28 to 40 Rc.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 particularly suitable for shafts of centrifugal pumps in marine service. In stagnant or slow-moving sea water, fouling may occur followed by pitting, but this pitting slows down after a fairly rapid initial attack.

Back to Top

Heat Treatment

Annealing is performed both for softening of the matrix after working and for solutioning of the age-hardening phase. Adequate softening may be achieved with temperatures as low as 1400-1600°F, but heating at 1800°F for hot-finished products and 1900°F for cold-drawn products is recommended for optimum response to subsequent age hardening. Grain growth becomes fairly rapid above 1800°F, and if a fine-grained structure is desired heating time should be kept to a minimum at these higher temperatures. For optimum aging response and maximum softness, it is important to obtain an effective water quench from the heating temperature without delay. A dely in quenching or a slow quench can result in partial precipitation of the age-hardening phase and subsequent impairment of the aging response. Addition of about 2% by volume of alcohol to the water will minimize oxidation and facilitate pickling. The following age-hardening procedures are recommended for achievement of maximum properties.

Back to Top

Machining

Heavy machining of alloy K-500 is best accomplished when the material is in the annealed condition or hot-worked and quenched condition. Age-hardened material, however, can be finish-machined to close tolerances and fine finished. The recommended practice, therefore, is to machine slightly oversize, age-harden, then finish to size. During aging, a slight permanent contraction (about 0.0002 in/in) takes place, but little warpage occurs because of the low temperatures and slow cooling rates involved.

Back to Top

Quality & Testing

Fushun supply Certification with all shipments, containing full chemical analysis and also mechanical test results if requested.

 

All incoming material is visually inspected and PMI (Positive Material Identification) tested before processing begins and all our production material is checked during each stage of processing.

 

All incoming orders are produced to the individual customer specification, some of which may involve processing sample batches for testing prior to full production.

 

Final Inspection carried out on all finished material to include:

Visual inspection

Dimensional checks

PMI (Positive Material Identification)

Mechanical tests

 

Nickel Alloy Material Available Formats

Fushun offers pure Nickel alloy materials in a variety of forms, including:

Seamless & welded pipe

Seamless & welded tube

Bar

Wire

Sheet

Plate

Forgings

Pipe fittings

Flanges

Weld Rod

 

Nickel Alloy Supply Quantities for Single Items or Full Bills

At Fushun, we can supply single items or full bills of nickel alloy materials for most any project. No inquiry is too small. We offer quick responses to customer inquiries and specialize in the rapid delivery of both large and small quantities of nickel alloy products.

 

Contact Fushun for Nickel Alloy Materials Today

Contact us for more information regarding our nickel alloy material options, or request a quote for further pricing details today. Fushun is your trusted nickel alloy supplier and manufacturer of premium nickel alloy materials.